Normal function noted in 4 high and 3 high. The manufacturer was made aware of the failure and did not offer any assistance. However as you can also see in my signature I only have a y33 Q as I sold the g50 q years ago so I also would not be inquiring about an axle seal on the G50. I found out that Toyota part 90404-51026 works perfectly with the threads in the axle. They still covered his under warranty. I was sold a lemon Nissan don't want to deal with.
The root cause is a poor breather system,. This is a major safety issue and the vehicle recalled for this problem. I was advised to not drive the truck due to possible axle and wheel separation from the rear end. Remove passenger side rear light. We have 12 reviews on our Differential Pinion Seal products for the 2007 Nissan Frontier from previous customers.
. Put the flat chisel against the race and drive it off. I am going to take them to court. The problem with seal replacement is it is difficult and time consuming and must be performed perfectly or the seals will leak again. But no bother I can tell that any information that is gathered from you is a bit suspect considering that you could not determine which vehicle I was refering too in my original inquiry about the axle seal.
I took my 2007 Nissan Frontier to the Nissan Dealership in Seaside, California to replace a seal on the right rear differential which was barely leaking. The bearing s were burnt and there was a fluid like sludge as a result of the heat. Oh, and Titans have a history of failed axle seals. I took the truck home rear differential was doing exact same thing but now rear was getting hot. I believe Nissan is aware of the problem but this part failure generates revenue, as the work is costly, and leads to the need for break replacement. Does anybody have any idea how to replace this that does not involve major muscle movement? You can buy the bearing and seal components seperate but you still need a shop to do the press work.
Man, this quote thing is really pissing me off. Although it's not the ideal way to do it you can use an air chisel to take the old bearing off. If I had not found this I could easily be dead due to wheel axle separation from the vehicle in motion. Took a day to get. Taken to Nissan dealer for inspection.
The last time, I was in my Jeep. Called another dealership had them pull up work done on truck and none was filed. No matter the situation, Advance Auto Parts has the Differential Pinion Seal product you desperately need. Consumer had the vehicle towed to the dealer for analysis, and mechanic noticed that the differential was worn out and needed to be replaced. Slide the pieces on and use the jaws of the vise to support the bearing and use a hammer to drive it together. It allows better ventilation to the axle. Every other post it just dont work.
It has rained around here before and been axle deep in flash flood waters getting out. I talked to my local Nissan shop and there answer was get a new axle or new roller and spacer and they can heat it u and cut the pieces off. The left front 4x4 hub cover was noted to be missing and the hub had spiral cracks all around it. My axles were replaced in 2012 along with breaks due to oil damage , now I'm being told 2015 that axles need to be replaced again. I shoulda wrote in my second write up why I did it in the first place. You can reassemble it in a vise if you don't have access to a press.
I got the seal and pulled the axle, what fun that was only to discover that the axle seal is mpossble to replace without a machine shop because there is a hydraulically pressed spacer after the bearing roller that keeps me from getting the seal off. There is a service bulletin at Nissan for this issue. After repair was performed the mechanic told me the rear axle housing vent tube clogged causing pressure to build up blowing out the rear seals. The spacer will crack and then you can slide it off. Route breather hose through frame. I took the truck in again, they took it in said they fixed the problems with the window and the rear end squeaking. No obvious external damage was noted at that time but there was a grinding noise noted when truck was put in 4 wheel drive low.