It goes quick so don't have your fingers where they can get pinched as the motor sucks in the plastic and the mast down into the hole. Note that the female end of the connector remaining in the kick panel cavity will not work with any standard male antenna cable end — it is too narrow. We advise you to take your car to an experienced mobile alarm installer or knowledgeable mechanic and have them troubleshoot your problem. The left handed drill bit sounds like a good choice. Aside from making the little mount, you can do the entire thing with a phillips, flathead and some pliers. Replacement specializes in body parts and lighting products; it also stocks electrical, brakes, suspension, intake, exhaust, cooling and heating parts. Might be too generic but might be enough to get you going.
One side goes to the radio, the other to the fender. Stop motor and insert bottom of antenna mast into tube. Follow all installation instruction on the package. Push it around curve at bottom of tube until end enters drive mechanism. Then a couple more bolts to remove the antenna motor. Hopefully the chrome sleeve will come with the old mast.
Pictures: Tundra Antenna Assembly view of passenger side kick panel cavity 6' generic antenna extension cable I had an 03 Tundra for many years and the same antenna survived the few automated car washes I sent it through. I should note that this is not a constant problem as sometimes it will go for a couple of weeks and then start again. Remove the glove box, and plastic side panel on the dash As you are looking through the removed area, there is a silver computer there, remove the bracket and move this computer. I could not use my old one Good luck! It will finally retract fully. Note direction of teeth on plastic drive wire.
The ground lead will be grounded to the panel next to the motor. If it is an automatic antenna, you can buy either the motor or the mast. On some General Motors and Ford you may need an adapter to mate the 2 cables together. If motorized, antenna has a white nylon gear tooth at back end. Screw the mast in place — Toyota supplies a little plastic wrench with the mast for this. Automotive wiring in a 2006 Toyota Tundra vehicles are becoming increasing more difficult to identify due to the installation of more advanced factory oem electronics. All Replacement brand items are backed by 1-year, unlimited-mileage warranty.
You need to remove the old broken plastic piece from the antenna motor. AutoTrust Gold Manual Antennas are guaranteed to meet or exceed the original manufacturer's standards and quality; Backed by a 5-year limited warranty; If the part breaks or is damaged - even if you are involved in a wreck or accident - anytime within 5 years from purchase, simply cover shipping and handling and we will send you a new part. Also, be aware and make sure that the new cable with stud matches the ant. This is a stock photo of what the power antenna unit and kit looks likes. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side.
Push up the plastic cover that shields the antenna motor, disconnect the power supply, and remove the bolt that holds the motor on the bracket. Only have to remove a few screws to get to it. But I don't like the retractables, manual or otherwise. Make sure the ignition key is completely off when performing the replacement. It was not easy, but it can be done. Behind the computer there will be the plug in for the antenna. One of the most time consuming tasks with installing an after market car stereo, car radio, satellite radio, xm radio, car speakers, tweeters, car subwoofer, crossovers, audio equalizer, car amplifier, mobile amp, car amplifier, mp3 player, ipod or any car audio electronics is identifying the correct color car audio wires for your 2006 Toyota Tundra.
Always verify all wires, wire colors and diagrams before applying any information found here to your 2006 Toyota Tundra. Assuming you just need to replace the mast, it comes with the plastic piece with the teeth on it. Replug it, and reinstall the computer and glove box door. Posted on Apr 04, 2009 Depending on if your car has a power antenna or not, you may have to replace the whole unit. Just don't let the weld leak out or your boned. I used the old grommet, because the Tundra cable has foam glued to parts of it and it was easier.
. Open your trunk, remove the insulating carpet from the side of the trunk where your antenna is located , to expose the power antenna unit. I found an old thread about using a 00-06 Tundra antenna assembly and mast. It took me a while to figure out why my sound sucked. Jul 09, 2009 Give these instructions a shot. We here at Auto Parts Warehouse want to make sure you're happy with your car part purchases. I re-used the mounting bolt from the old antenna motor.
It worked for me and I am happy so I thought I would expand on it a little for those who want to go this way. Then cram the new plastic runner as far as you can into the hole that leads to the antenna motor. Unscrew the plastic ring on the outside of the car, where the antenna rest on the body of the vehicle. You will have to un-install the entire antenna system from the inside. The plastic cable can be inserted freely to about 12 inches and will stop. The bezel usually screws into the motorized device underneath the body work. Be careful not to drop them down too far.