Mazda 6 Atenza and noticed that there is a light on the dashboard that is continually. When towing, trailer tongue load or king pin weight is also part of cargo weight. Dashboard warning lights serve a very important function. Refer to the Seat belt maintenance section in this chapter. Airbag indicator This signals a malfunction with the airbags or airbag sensor. But if you ignore it, your motor could end up looking like a frying pan that's been left on the burner for a few hours.
Remove the jumper cable from the ground metal surface. Grab the bottom of the trim and pull strait back. Each time you do the counter will reset even if its the right key. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. When changing the air filter element, only use a genuine Mazda air filter element. Press and release to lock all the doors. Turned out the brake fluid was low.
This indicates the seat belt is now in the automatic locking mode. Wait until the seat belt warning light turns off Approximately one minute. This is the quickest and best way to address the issue. The side airbag system including the seat must be inspected and serviced by an authorized dealer. If you get any red warning lights. Some lights, like your check engine indicator, can be triggered by multiple issues. If problem affects both lights this will not trigger the warning as the current to both lights is the same, zero.
I hope that with all of the complaints I have read about this, someone will realize that it is a real problem, before someone does get hurt or killed. Protecting the environment We must all play our part in protecting the environment. Use of a recycled engine coolant which does not meet the Mazda recommended coolant, may harm engine and cooling system components. Low pressures carry increased risk of a blowout on the highway due to tire overheating. Children and airbags For additional important safety information, read all information on safety restraints in this guide. The manufacturer was made aware of the issue.
Press the clutch pedal to the floor, then put the gearshift lever in the neutral position. The contact took the vehicle to a dealer and was told that the spring tensioner for the air bag needed to be replaced. The menu listing will display the opposite state. Wait until the weather clears before trying to drive with the wipers inoperative. Make sure the headlamp switch is in the off position, then open the liftgate to expose the lamp assembly screws. What some of the dashboard symbols in your car mean? I am trying to figure out what that lite means.
It does not include passengers, cargo, or optional equipment. Removing the jack and tools The jack and tools are located under the carpeted load floor. Shield your eyes when working near the battery to protect against possible splashing of acid solution. Heated outside mirrors if equipped Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. That exclamation light on the dash board indicates low. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
It is warning you that your car will blow up in the next 3 weeks if you do nothing Anonymous. The contact stated that the vehicle was taken to the dealer on numerous occasions to be diagnosed, however the failure could not be determined. If you must use a forward-facing child seat in the front seat, move the vehicle seat all the way back. The system will prompt you to load discs for the remaining available slots. This can lead to loss of control or an accident. Mazda does not recommend disabling this feature except in situations where speed reduction may be detrimental e.
To remove, open the console lid and pull the bin straight up and out from the console housing. When the grooves in the plastic base are aligned, turn the new bulb clockwise to install. Note: Do not wipe off any grease on the battery terminals on the back surface of the circuit board. Car dashboard warning lights call Gil Auto when they light up. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label.
You have to find the co … rrect place to push in, before they will come apart. E pendable parts, tightening torques and symbols for oil, grease, and sealant are. Bounce-back override: To override bounce-back, press and hold the front portion of the control. Turn the ignition from the 1 off position to the 3 on position. On— all electrical circuits operational and warning lights will illuminate. Connect the negative - cable to the negative - terminal of the assisting battery.